- What gear ratio is better for acceleration?
- Is 3.55 or 3.73 gears better?
- Does bigger tires change gear ratio?
- Are 4.11 gears good?
- Are 3.73 gears good?
- Are 3.73 or 4.10 gears better?
- How do I figure out what gear ratio I need?
- What is the best first gear ratio?
- Are 4.10 gears good for highway?
- Does higher gear ratio mean faster?
- What gear ratio is best for fuel economy?
- What’s the best gear ratio for highway driving?
- At what RPM gear should be changed?
- Does a lower gear ratio increase torque?
- What gear ratio should I use for 33 inch tires?
- Is 3.42 or 3.73 better?
- Is a 4.10 gear ratio good?
- How fast can you go with 4.10 gears?
- Is 3.08 a good gear ratio?
- Is 3.23 a good gear ratio?
- Does gear ratio affect horsepower?
What gear ratio is better for acceleration?
When accelerating from 50 to 70 mph, engine speed increases by about 800 rpm.
Put 4.10:1 gears in the same car, and engine speed increases by 1060 rpm—the difference is 40 rpm per mph with the 3.08s versus 53 rpm per mph for the 4.10s.
The greater rate of rpm increase versus road speed provides greater acceleration..
Is 3.55 or 3.73 gears better?
3.55 will give you a little better gas mileage on the highway and slightly more highway oriented performance. 3.73 may be better for towing, lower end power (off the line acceleration), and may result in worse gas mileage on the highway.
Does bigger tires change gear ratio?
Taller than stock tires alter the final drive ratio of your 4×4 at the tires and effectively decrease the power you can put to the ground. The bigger the tires are, the more noticeable the change. The added weight and wind resistance also tax the engine.
Are 4.11 gears good?
4.11:1 is a “lower” gear ratio, meaning you have more torque, lower top speed, and you will generally consume more fuel. Usually people put 4.11:1 gears in trucks to be used off-road for the extra torque and the better “crawling” capabilities.
Are 3.73 gears good?
A numerically higher axle ratio provides a mechanical advantage to send more of the engine’s available torque to the rear tires (and front tires, in a four-wheel drive vehicle), but you pay the price at the fuel pump. So, a truck with optional 3.73 gears will tow a heavier trailer than one with 3.55 or 3.21.
Are 3.73 or 4.10 gears better?
Vice versa, if the gear ratio is lower it has worse acceleration but a higher top speed….WHICH GEAR RATIO IS FOR YOU?3.73 RATIO4.10 RATIOSlower off the lineQuicker off the lineLower torqueHigher torqueBetter gas mileageWorse gas mileageHigher top speedLower top speedMay 12, 2020
How do I figure out what gear ratio I need?
The gear ratio is calculated by dividing the output speed by the input speed (i= Ws/ We) or by dividing the number of teeth of the driving gear by the number of teeth of the driven gear (i= Ze/ Zs).
What is the best first gear ratio?
10:1For most street performance applications, a 10:1 final First gear ratio is usually considered optimal. The disadvantage of operating a 4.10:1 axle ratio on the street with a 1:1 high gear is excessive freeway engine speed.
Are 4.10 gears good for highway?
Installing 4.10 gears improves the car’s performance on the track but with negligible effects to the highway driving. … Switching from a gear set of 3.55 or 3.73 to 4.10 gears will affect your gas mileage slightly as your engine will be turning more times to rotate the rear wheels once.
Does higher gear ratio mean faster?
A lower (taller) gear ratio provides a higher top speed, and a higher (shorter) gear ratio provides faster acceleration. . Besides the gears in the transmission, there is also a gear in the rear differential.
What gear ratio is best for fuel economy?
The lower the number, the better fuel economy, and the higher the number the more towing power you have, but fuel economy suffers. For instance, a 3:31 gets better fuel economy than a 3:73. On the other hand, a 3:73 or perhaps a 4:10 will tow much more, while fuel economy greatly drops.
What’s the best gear ratio for highway driving?
Rear end gears (2.79’s, 3.00’s, 3.25’s, etc) are great for freeway driving, bit not good for 0-60 MPH or accelerating from a dead stop. Shorter gears (higher numbers) are much better suited for accelerating, such as 3.55, 3.73, 3.91’s, 4.11’s etc. Always remember, for very “give” there is a “take”.
At what RPM gear should be changed?
Generally, you should shift gears up when the tachometer is around “3” or 3,000 RPMs; shift down when the tachometer is around “1” or 1,000 RPMs. After some experience with driving a stick shift, you’ll be able to figure out when to shift by the way your engine sounds and “feels.” More on that below.
Does a lower gear ratio increase torque?
In general, a lower final drive ratio will lead to less torque at the wheels but a higher top speed. Meanwhile, a higher ratio will result in the opposite, i.e. more torque at the wheels but a lower top speed.
What gear ratio should I use for 33 inch tires?
So if our truck had 30-inch tires stock, and a 3.73:1 axle ratio, that calculation would tell us we need a 4.103:1 (which rounds off to the readily available 4.10:1) gear ratio to get us back to stock with 33-inch tires.
Is 3.42 or 3.73 better?
The difference in towing mpg between the 3.42 and 3.73 gears at highway cruise speed, under the same conditions, should be less than 1 mpg because of the slightly higher rpm running 3.73s. Vehicle speed actually plays a bigger role in fuel economy than engine rpm.
Is a 4.10 gear ratio good?
FACT: A 4.10 axle ratio is ideal for towing heavy loads in a mix of city and highway driving and when towing on varied or steep grades. A 4.10 axle ratio will provide improved acceleration in stop and go city traffic.
How fast can you go with 4.10 gears?
On the highway a 4.10 gear will only be about 200 rpms more at around 75 then a 3.73. And with the Automatic you will need all the help you can get. Top Speed of our GT’s should be between 145 and 155 depending on the tune of your chip if you have one.
Is 3.08 a good gear ratio?
Two common base axle ratios for trucks are 3.08 and 3.42. A 3.73 ratio is suitable for regular light towing. If you plan on towing a fifth-wheel trailer or anything heavier than 5,000 pounds, you should consider a 4.1 axle ratio. A 4.1 ratio allows a towing vehicle to start moving without as much throttle.
Is 3.23 a good gear ratio?
The engineers likely chose the numerically low gear ratio for fuel economy reasons. … A later swap to a four-speed and 3.23 rear gears woke up the performance of the car considerably. Yes, highway rpm increased as well, but I rationalized it by deciding that 3.23 gears provided a good balance of performance and economy.
Does gear ratio affect horsepower?
Motor HP does not change when you change gear ratios. The only thing that changes is torque. A dynamometer measures torque and RPM, and from those two values calculates horsepower. When you change gear ratios both RPM and torque will change but horsepower will not.