Quick Answer: WHAT WILL 4.10 Gears Do?

What’s the difference between 4.10 and 4.11 gears?

the difference between 4.10 and 4.11 is that 4.10s have 41 ring gear teeth and 10 pinion teeth.

4.11s have 37 ring gear teeth and 9 pinion teeth.

same way that 45 ring gear teeth and 11 pinion teeth will give you 4.09s..

Is 3.23 a good gear ratio?

The engineers likely chose the numerically low gear ratio for fuel economy reasons. … A later swap to a four-speed and 3.23 rear gears woke up the performance of the car considerably. Yes, highway rpm increased as well, but I rationalized it by deciding that 3.23 gears provided a good balance of performance and economy.

Is it better to have a higher or lower gear ratio?

A numerically higher ratio — say, 3.9 as opposed to 3.2 — can pull heavy loads much better but has a worse fuel economy and lower speed. By contrast, a numerically lower ratio has better fuel economy but worse torque and towing power.

Are 3.73 or 4.10 gears better?

Vice versa, if the gear ratio is lower it has worse acceleration but a higher top speed. So, by changing your gear ratio, no power levels are being changed, just the torque….WHICH GEAR RATIO IS FOR YOU?3.73 RATIO4.10 RATIOBetter gas mileageWorse gas mileageHigher top speedLower top speed2 more rows•May 12, 2020

How much does it cost to have a ring and pinion install?

Depending on the year, make, and model of your vehicle, the cost of an aftermarket ring and pinion set may fall anywhere between $50 and $1,700. The ring and pinion gears can be purchased per piece, in sets of two, or part of a kit.

Is 3.42 or 3.73 better?

The 3.42 is fine for towing smaller boats, plus you will get better gas mileage for everyday driving. If I were towing frequently on hilly roads, I might would go for the 3.73 for better gas mileage while towing, but the 3.42 should be fine with a 205.

Is 3.55 or 3.73 gears better?

3.55 will give you a little better gas mileage on the highway and slightly more highway oriented performance. 3.73 may be better for towing, lower end power (off the line acceleration), and may result in worse gas mileage on the highway.

What does a 4 11 gear ratio mean?

The number refers to the pinion to ring gear ratio in the differential. This is a ring and pinion gear: In a 3.73:1 gear set, the pinion gear turns 3.73 times for every rotation of the ring gear. … The 4:11 Gears will get you faster acceleration higher rpm at any given speed and increased fuel consumption.

How much does it cost to get 4.10 gears installed?

Installation costs will vary, but a good rule of thumb is between $250 and $300. Be sure to work with a reliable shop that you trust for installations. You can also save money on your installation labor by having your Trac-Lok rebuilt at the same time as your gears are installed, see drop down option above.

Are 4.10 gears good for highway?

Installing 4.10 gears improves the car’s performance on the track but with negligible effects to the highway driving. … Switching from a gear set of 3.55 or 3.73 to 4.10 gears will affect your gas mileage slightly as your engine will be turning more times to rotate the rear wheels once.

How much does it cost to have Gears installed?

Dealers typically charge about $90-$95 per hour. Speed shops usually charge about $80-$120 per hour, so labor “should” be about $300-$400 for a properly installed gear set that’s done-right-the-first-time. Add in cost of parts, supplies, fluids, shims, bearings, etc.

Does gear ratio affect horsepower?

Motor HP does not change when you change gear ratios. The only thing that changes is torque. A dynamometer measures torque and RPM, and from those two values calculates horsepower. When you change gear ratios both RPM and torque will change but horsepower will not.

What are 4.11 gears good for?

4.11:1 is a “lower” gear ratio, meaning you have more torque, lower top speed, and you will generally consume more fuel. Usually people put 4.11:1 gears in trucks to be used off-road for the extra torque and the better “crawling” capabilities.

What gear ratio is best for speed?

If you prefer top speed to dragstrip performance, then higher axle gears, like 2.76:1 or 3.08:1, may be called for. The higher gears will reduce engine rpm versus road speed. Another way to look at it is that the car will go faster at the engine’s rpm limit than it would with lower gears.

What gear ratio is best for fuel economy?

The lower the number, the better fuel economy, and the higher the number the more towing power you have, but fuel economy suffers. For instance, a 3:31 gets better fuel economy than a 3:73. On the other hand, a 3:73 or perhaps a 4:10 will tow much more, while fuel economy greatly drops.

How fast can you go with 4.10 gears?

On the highway a 4.10 gear will only be about 200 rpms more at around 75 then a 3.73. And with the Automatic you will need all the help you can get. Top Speed of our GT’s should be between 145 and 155 depending on the tune of your chip if you have one.

Is a 4.10 gear ratio good?

FACT: A 4.10 axle ratio is ideal for towing heavy loads in a mix of city and highway driving and when towing on varied or steep grades. A 4.10 axle ratio will provide improved acceleration in stop and go city traffic.

Are 3.73 gears good for highway?

Rear end gears (2.79’s, 3.00’s, 3.25’s, etc) are great for freeway driving, bit not good for 0-60 MPH or accelerating from a dead stop. Shorter gears (higher numbers) are much better suited for accelerating, such as 3.55, 3.73, 3.91’s, 4.11’s etc. Always remember, for very “give” there is a “take”.

Does higher gear ratio mean faster?

A lower (taller) gear ratio provides a higher top speed, and a higher (shorter) gear ratio provides faster acceleration. . Besides the gears in the transmission, there is also a gear in the rear differential.

Do gears make car faster?

The simple answer is yes. More aggressive gearing creates a quicker car but not a faster car. A gearing change will have a noticeable affect on your car. If you swap in taller rear gears, you can gain some top-end speed, making your car faster, but you’re going to be a bit slower leaving from a stop.

What is the best gear ratio for 35 inch tires?

Depending on the axle, the next lowest ratio from a 4.10:1 is most likely the 4.56:1, which should be selected for towing and performance. Because of the extra weight associated with off-road tires, we usually recommend going with a performance-minded gear ratio for any tire size above 35 inches.